Catalog - One Source (PF14434) - Flipbook - Page 350
IC Lift Truck Tools
C-5 Brake Tools
Continued
C-5 Transaxle Tools
SAHR Cap Tool
Part Number - 360057
Used for C-5 power brake equipped lift trucks
to remove and install brake SAHR cap.
Pinion Shaft Nut Socket
Part Number - 360060
Used with transaxle socket tool 360055 as a
drive/extension to loosen and tighten pinion
shaft nut.
C-5 Engine Tools
Compression Gauge
and Hose Assembly
Part Number - 145739
High Quality Snap on Engine Compression
Gauge for measuring cylinder compression
on internal combustion engines.
Accessory Items: Compression Test
Assembly (P.N. 145006)
Adapter to be used with the 145739 Engine
Compression Gauge. This is required for
measuring cylinder compression on C-5,
RST-50 and RP-50 internal combustion forklifts.
Replacement part: Schrader valve/check
valve - P.N. 145740
WARNING: Cancer and reproductive harm - www.P65Warnings.ca.gov
4024 Electronic Data Link Kit
TOOLS
Part Number - 164229
Used for downloading RST-50 & C-5 software
into truck.
Trans Puller Set With Bag
Part Number - 360056
Used for C-5 & RST transaxle rebuilds to
remove internal bearings.
Spanner Wrench
Part Number - 360046
Used to assemble and tighten C-5 differential
carrier bearing adjuster ring nut.
Axle Bearing Tool
Part Number - 145012
Used to assist in removing drive axle hubs.
Fits into end of of axle on RST-50 and C-5
models to give puller tool a platform to press
against.
Bushing Installation Tool
Part Number - 144931
Wrench Fan Bearing
Bushing
Part Number - 360054
Used to tighten or loosen engine fan on
RST-50 & C-5 models without ODC.
Hydraulic Lifter Bleed Down Tool
Part Number - 141920
Used to disperse oil from the lifters on
C-5 when replacing the cylinder head.
A 144998 flywheel timing lock pin is also
recommended.
KIRA Diagnostic Tool
Part Number - 323098
IMAGE NOT
AVAILABLE
Basic configuration. Used for C-5 Diesel trucks
with Kohler engine. Contact Crown Technical
Support for activation. Requires a 3 year
subscription fee (first 3 years included with
purchase of tool).
Cable from VCI diagnostic connector
to DEUTSCH (P.N. 323099).
WARNING: Cancer and reproductive harm - www.P65Warnings.ca.gov
Used to install drive axle bushings (145321)
on RST-50 and C-5 models.
Axle Hub Alignment Tool
Part Number - 143129
Used to install drive axle hub on RST-50 and
C-5 models. Helps align hub and protects
hub seal when installing drive hubs. Use with
143130 axle hub alignment tool.
Axle Hub Bearing Driver Tool
Part Number - 143130
Used to install drive axle hub on RST-50
and C-5 models. Use with 143129 axle hub
alignment tool.
Hub Seal
Installation Tool
Part Number - 065208
Used to install drive hub inner seals on RST-50
and C-5 models. Helps to positon seal at the
correct depth and prevents seal damage.
WARNING: Cancer and reproductive harm - www.P65Warnings.ca.gov
Transmission Pressure Test Kit
Part Number - 360042
C-5 Transaxle Tools
Transaxle Socket Tool
Part Number - 360055
C-5 transaxle dual purpose socket for C-5
transaxle rebuild. Also, works with Pinion Shaft
Socket 360060 to loosen and tighten pinion
shaft nut. Long socket extension used with a
press to compress clutch shaft friction plate
spring for friction plate removal.
9.22 Crown One Source
Used for checking C-5/RST transmission
pressures during troubleshooting.
WARNING: Cancer and reproductive harm - www.P65Warnings.ca.gov
Pinion Shaft Socket
Part Number - 360047
Used to set pinion shaft bearing per load on
C-5 transaxle.
