Catalog - One Source (PF14434) - Flipbook - Page 338
Diagnostic Tools
Continued
Multimeter Accessory Items
Used with Part Numbers - 121357 and 121359
Thermocouple Probe
Part Number - 300091
One piece construction with banana jack.
Measurement range: -40 to 500ºF (-40 to 260ºC)
Type K
Meter Kit (P.N. 100696)
Multimeter Fluke Series 179
Part Number - 121357
Precise readings of A.C. or D.C. voltage, resistance, low current
and frequency. Required for wire guidance systems. Used also for
electrical troubleshooting. Includes: 179 Series multimeter, yellow
holster, test leads, batteries and instruction manual.
Kits: Meter Kit - (P.N.100696), includes Fluke Meter, Carrying Case,
Test Leads, and Thermocouple Probe.
Multimeter Fluke Series 87
Series III True RMS
TOOLS
Part Number - 121359
Precise readings of A.C. or D.C. voltage,
resistance, low current and frequency.
Required for wire guidance systems. Used
also for electrical troubleshooting. Includes:
87 Series multimeter, yellow holster, test
leads, batteries and instruction manual.
Includes: Thermocouple Probe.
Accessory Items: Holster (P.N. 121360),
Test Lead Assembly (P.N. 321359)
Fluke Meter 3000 Series
Part Number - 321357
Precise readings of AC or DC
voltage, resistance, low current and
frequency with this wireless digital
multimeter.
Shrouded Test Kit
Part Number - 121421
For use with multimeters that
accept shrouded standard
diameter, 0.16” (4mm), banana
plugs. Manufacturer instructions
included. Includes: 2 - #18 AWG (0.75mm2)
test leads 48” (1.2m) long, one red, one black. Two
insulated alligator clips with banana jacks, 5/16” (7.9 mm) jaw
opening. Two spade lugs. One safety-grip spring loaded hook
style test clip. One test lead pouch.
Test leads 59" (1.5 m) long; one red, one black (P.N. 301501)
Lead Set (Clip-on)
Part Number - 101490
For use with digital (VOM) multimeter
on printed circuit boards and close
areas where standard tips may short
out components. Required on wire
guidance P.C. boards such as sensor
amplifier boards. Includes: 2 leads with jacks
and spring loaded probes (1) red and (1) black.
WARNING: Cancer and reproductive harm - www.P65Warnings.ca.gov
Backprobe Pin Set
Part Number - 320067
Slides onto test lead, narrowing the point
of contact for the test lead to be used in
narrow situations or hard to reach areas.
Tool Carry Case
Part Number - 128321
Probe Set
Part Number - 102973
Fluke 325 True RMS Clamp Meter
Part Number - 109040
Rugged, reliable True-RMS clamp meter with
DC current and frequency measurements.
Measures AC and DC voltages to 600 V.
Measured AC and DC current to 400 A.
Provides True RMS AC voltage and current for
accurate measurements on non-linear signals.
Measures frequency to 500 Hz. Measures
resistance to 40 kilo-ohms with continuity
detection.
Probe Set
Part Number - 300600
The EAP Kit is designed for electronic systems in
which precision is mandatory. Each probe mirrors a
back-pinning probe, a piercing probe, and a pin-tip
probe. Probes are repairable if they bend or break.
WARNING: Cancer - www.P65Warnings.ca.gov
Current Clamp
Part Number - 109039
For accurate measurement of AC or DC up to
1000A current draw on battery without inline
shunt connection. Includes instructions.
9.14 Crown One Source
Field Strength Meter
Part Number - 112953
To check field strength of guide wire. Label on
meter with instructions. See TSB 317.
