Catalog - One Source (PF14434) - Flipbook - Page 346
IC Lift Truck Tools
Continued
C-5 Transaxle Tools
C-5 Engine Tools
Compression Gauge
and Hose Assembly
Part Number - 145739
High Quality Snap on Engine Compression
Gauge for measuring cylinder compression
on internal combustion engines.
Accessory Items: Compression Test
Assembly (P.N. 145006)
Adapter to be used with the 145739 Engine
Compression Gauge. This is required for
measuring cylinder compression on C-5,
RST-50 and RP-50 internal combustion forklifts.
Replacement part: Schrader valve/check
valve - P.N. 145740
4024 Electronic Data Link Kit
Part Number - 164229
Used for downloading RST-50 & C-5 software
into truck.
Spanner Wrench
Part Number - 360046
Used to assemble and tighten C-5 differential
carrier bearing adjuster ring nut.
Axle Bearing Tool
Part Number - 145012
Used to assist in removing drive axle hubs.
Fits into end of axle on RST-50 and C-5models
to give puller tool a platform to press against.
Bushing Installation Tool
Part Number - 144931
Used to install drive axle bushings (145321)
on RST-50 and C-5 models.
Axle Hub Alignment Tool
C-5 Transaxle Tools
Transaxle Socket Tool
Part Number - 143129
Used to install drive axle hub on RST-50 and
C-5 models. Helps align hub and protects
hub seal when installing drive hubs. Use with
143130 axle hub alignment tool.
TOOLS
Part Number - 360055
IMAGE NOT
AVAILABLE
C-5 transaxle dual purpose socket for C-5
transaxle rebuild. Also, works with Pinion Shaft
Socket 360060 to loosen and tighten pinion
shaft nut. Long socket extension used with a
press to compress clutch shaft friction plate
spring for friction plate removal.
Pinion Shaft Nut Socket
Part Number - 360060
Used with transaxle socket tool 360055 as a
drive/extension to loosen and tighten pinion
shaft nut.
Trans Puller Set With Bag
IMAGE NOT
AVAILABLE
Axle Hub Bearing Driver Tool
Part Number - 143130
Used to install drive axle hub on RST-50
and C-5 models. Use with 143129 axle hub
alignment tool.
Hub Seal
Installation Tool
Part Number - 065208
Used to install Drive hub inner seals on RST-50
and C-5 models. Helps to positon seal at the
correct depth and prevents seal damage.
WARNING: Cancer and reproductive harm - www.P65Warnings.ca.gov
Part Number - 360056
Used for C-5 & RST transaxle rebuilds to remove
internal bearings.
Transmission Pressure Test Kit
Part Number - 360042
Used for checking C-5/RST transmission
pressures during troubleshooting.
C-G Tools
PSI Diagnostic Tool
Part Number - 101529-00207
For both Crown C-G and Hamech units. Using the
E-Controls GCP Diagnostic Scan Tool (DST), the
Technician can not only read Trouble Codes, but
also view real-time streams of Engine Sensor Data.
PSI Diagnostic Plug
Part Number - 33001197
For both Crown C-G and Hamech units. Allows
you to retrieve Trouble Codes without using the
GCP Diagnostic Scan Tool.
!
NEW
PSI Adapter Cable
Part Number - 430201-02466
Engine diagnostic connector for the CGC 35-55-9
Cushion, CG NXP, and CG 35-50-7 Pneumatic.
Used with the 101529-00207 PSI Diagnostic
Tool.
9.22 Crown One Source
Pinion Shaft Socket
Part Number - 360047
Used to set pinion shaft bearing per load on
C-5 transaxle.
