Catalog - One Source (PF14434) - Flipbook - Page 331
Mechanical Tools
Axle Remover
Part Number - 090705
For single or dual load wheel axle removal on
PE, PC, PR, PW trucks. One piece tool.
Replacement rods/set of 2 - P.N. 320066
WARNING: Cancer and reproductive harm - www.P65Warnings.ca.gov
Roll Pin Insertion and
Extraction Tool
Part Number - 110567
Removal and installation of load wheel axle
roll pin. Used on Stockpickers and
RR/RD 3000 and 5000 Series.
Continued
Quick Change Load Wheel
Installation Tool
Part Number - 150192 (for 2.88" load wheel)
Part Number - 150193 (for 4.12" load wheel)
Used to install quick change load wheels on
Reach trucks.
Tire Adapter
Part Number - 134169
Used to press drive tire on RR/RD 5000
Series trucks. See PIB 05-08-02.
WARNING: Cancer and reproductive harm - www.P65Warnings.ca.gov
WARNING: Cancer and reproductive harm - www.P65Warnings.ca.gov
Steer Bearing Cup Removal Kit
Auxiliary Mast Lifting Tool
Part Number - 110571
Facilitates handling auxiliary mast. Used on
TS. Refer to platform maintenance of service
manual, (section 9.0). One piece tool.
Part Number - 133884
Used to push cup-holder off of undercarriage
dowel pins after bolt removal. Used on all
RR5, RM6, RM1, and SP4 models.
Individual Items: Push-Off Bolt (P.N. 060133)
WARNING: Cancer and reproductive harm - www.P65Warnings.ca.gov
Gage Shim Assembly
Part Number - 125535
Gage used to shim Wave masts. Used with
Part Numbers 125539 and 133403. See
maintenance section for where used.
Part Number - 125539
Gage used to shim Wave masts. Used with
Part Numbers 125535 and 133403. See
maintenance section for where used.
Part Number - 810705
ESR4000 Mast Tool used to calculate the
required roller diameter.
Shield / Screen Installation Tool Tapered Tip
Part Number - 340020-001
Used to install shields on RR/RD 5000 series,
Stockpicker and Turret trucks
Gage Shim Assembly
Part Number - 133403
Gage used to shim Wave masts. Used with
Part Numbers 125535 and 125539. See
maintenance section for where used.
Shield / Screen Installation Tool Complete Kit
Part Number - 340020-002
Used to install shields on RR/RD 5000 series,
Stockpicker and Turret trucks.
Spanner Tool
Part Number - 100455
For removal, installation and torquing the axle
locknuts. Used on RC, SC, Reach, TSP, TS
and SP 3000 Series.
Tool Assembly
Part Number - 132501
Used for installation of load wheels on
stockpickers, WR and reach trucks with an axle
diameter of 1.375. This tool aligns the shims
and wheels to make it easier to get the axles in.
Hole Cutting Tool Arbor
Shank with Pilot Pin - Hougen
Part Number - MSC98380876
Minimum tool diameter compatibility: 13⁄16".
Maximum tool compatibility: 11⁄2". Shank
diameter: 1⁄2". No. of flats: 3. Material: Steel.
Weldon flat: No.
Straight shanks are used for general purpose
applications. The shank is smaller than
the drill bit diameter. They are used with
portable drills and drill presses on ferrous and
nonferrous materials.
Tool Assembly
Part Number - 132502
Used for installation of load wheels on
stockpickers, WR and reach trucks with an axle
diameter of .975. This tool aligns the shims and
wheels to make it easier to get the axles in.
3rd Stage Mast Locking Bar Tool
Part Number - 150796
Used to move mast stops on RM/RMD series
mono masts.
Primary Lift Cylinder
Retention Tool
Part Number - 164857
Used on RM 6000 to restrain the primary
lift cylinder while raising the 2nd & 3rd mast
stages. Used in the removal and installation of
the reach assembly.
Tools 9.07
TOOLS
Gage Shim Assembly
Mast Tool
